Steel’s Continued Reinvention: New Advanced Steel Grades Meet Growing Automaker Demands
DETROIT, Aug. 7, 2012 /PRNewswire/ — An increasing number of recently published studies about advanced high-strength steel (AHSS) reveal that it has become the lightweight automotive material that best addresses society’s need for reduced greenhouse gas emissions, without compromising safety, performance or affordability, according to Ron Krupitzer, vice president, automotive market, Steel Market Development Institute, a business unit of the American Iron and Steel Institute.
The development of AHSS grades has been driven by the ever-increasing challenges faced by automakers, such as crash performance requirements, the need to reduce vehicle mass for fuel efficiency and the need to enhance formability to manufacture high-strength parts.
“The advanced grades are relatively new to vehicle design and are significantly different from the conventional steels they replace,” Krupitzer said. “The lightweighting capability of AHSS results from their unique combination of strength and ductility. These attributes are developed by creating specific microstructures through precise and tightly controlled steelmaking processes. The results are lightweight automotive designs that are cost effective with low emissions that also provide unmatched safety performance.”
Below are some key advantages of AHSS:
Safety and Durability Performance
- As shown in WorldAutoSteel’s recent FutureSteelVehicle (FSV) study, using today’s design optimization tools, a steel body structure with 35 percent weight savings can meet or exceed all safety requirements.
- Steel remains the dominant material for automotive bodies and safety cages.
- Consumers value the safety benefits of steel. When asked which automobile components protect them most, the top three choices by consumers were seat belts, steel frames (the steel safety cage) and steel side-impact beams (placed inside car doors to better protect passengers in side-impact collisions).
- Steel is recycled more than all other materials on the planet combined, with an extremely high overall recycling rate. Recycling of automotive steel can top 100 percent, as the cars being recycled may be heavier than new models.
- Because it is 100 percent recyclable, steel used in today’s cars can help automakers reduce the carbon footprint of tomorrow’s vehicles.
- Automobiles are recycled more than any other consumer product, with nearly 100 percent of vehicles being recycled for their iron and steel content. In 2008, this resulted in more than 14.8 million tons of steel was recovered for reuse from scrapped automobiles.
- Life cycle assessment (LCA) is an established method of accounting for total greenhouse gas emissions associated with products like automobiles and determines the carbon footprint of products. Steel is the only material that reduces greenhouse gas emissions in all phases of a vehicle’s life: manufacturing; driving; and end-of-life.
- LCA shows that steel, which currently makes up about 60 percent of the average North American vehicle, generates fewer emissions than other automotive body materials; therefore, steel-intensive automobiles will continue to be the overall lowest-emitting vehicles on the road.
- The use of AHSS reduces a vehicle’s structural weight by as much as 25 percent (35 percent with the FSV) and can cut total life cycle CO(2) emissions by up to 15 percent more than any other automotive material, according to a WorldAutoSteel LCA study.
- The Massachusetts Institute of Technology study “Process Cost Modeling: Strategic Engineering-economic Evaluation of Materials Technologies” and related cost models identify alternative materials to be at a significant cost disadvantage for all aspects of the body-in-white manufacturing process. For example:
- In raw material costs, aluminum is three times more expensive than steel;
- In conversion costs, aluminum is two times more expensive than steel;
- In assembly, aluminum is 20 to 30 percent more expensive than steel; and
- In total, an aluminum structure is estimated at 60 to 80 percent more expensive than a conventional steel design.
- Optimized steel body structures using AHSS can be constructed at no significant additional cost relative to a conventional body structure.
AISI serves as the voice of the North American steel industry in the public policy arena and advances the case for steel in the marketplace as the preferred material of choice. AISI also plays a lead role in the development and application of new steels and steelmaking technology. AISI is comprised of 25 member companies, including integrated and electric furnace steelmakers, and 124 associate members who are suppliers to or customers of the steel industry. AISI’s member companies represent over three quarters of both U.S. and North American steel capacity.
The Steel Market Development Institute (SMDI) grows and maintains the use of steel through strategies that promote cost-effective solutions in the automotive, construction and container markets, as well as for new growth opportunities in emerging steel markets. For more news or information, visit www.autosteel.org or follow us on twitter at www.twitter.com/smdisteel.
SMDI investors include:
- AK Steel Corporation
- ArcelorMittal Dofasco
- ArcelorMittal USA LLC
- Nucor Corporation
- Severstal North America Inc.
- ThyssenKrupp Steel USA, LLC
- United States Steel Corporation
SOURCE Steel Market Development Institute