Quantcast

Gentor Resources and Al Fairuz Mining Extend their High Grade VMS Mahab 4 Deposit in Northern Oman

May 26, 2011

Results include massive sulphide intersections of 30.95 metres grading
3.16% Cu, 0.28 g/t Au, 1.29% Zn and 17.4 g/t Ag from 32.05 metres down
hole, and 20.30 metres grading 5.79% Cu, 0.37 g/t Au, 2.42% Zn and
22.04 g/t Ag from 67.15 metres depth

TORONTO, May 26, 2011 /PRNewswire/ – Gentor Resources, Inc. (“Gentor” or the
“Company”) (OTCQB – “GNTO”) and its Omani partner Al Fairuz Mining
Company LLC are pleased to announce further excellent results from the
Company’s second drilling program at its Oman copper/gold properties.

In February of this year, Gentor recommenced diamond drilling on its
Block 5 concession in the Sohar copper mining region, and has succeeded
in expanding the size of its two new volcanogenic massive sulphide
(VMS) discoveries at Mahab 4 and Maqail South that resulted from
testing conductors defined by a VTEM heliborne survey in 2010.
Encouraging massive sulphide (MS) results from these prospects at the
main mineralised stratigraphic position within the Oman Ophiolite
Complex were previously reported on by Gentor in press releases dated
November 11, 2010 and January 5, 2011.

Assay results have now been received from three holes out of a program
of eight core holes totalling 960 metres completed by the end of April
on three 50-metre spaced sections at the Mahab 4 prospect. These holes
tested the northern strike and dip extent of the promising initial MS
intersections located adjacent to a major north trending fault
separating footwall and hanging wall volcanics.

All three assayed holes provided strong verification of high-grade
massive and semi-massive sulphides (SMS) within a proximal seafloor
mound and footwall stringer vein system (QVS). Together with further
intersections not yet assayed the diamond core drilling has extended
the deposit along strike for at least 200 metres at depths from 40 to
130 metres, and downdip up to 50 metres to the east.

Locality plans of the prospect area and reported drill holes on sections
are found accompanying this press release on the Company’s web site at:
http://www.gentorresources.com/s/NewsReleases.asp?ReportID=459300

Gentor’s President and CEO Dr. Peter Ruxton commented: “These new drill
results confirm our expectations that the Mahab 4 prospect is likely to
deliver a shallow open-pittable high-grade copper resource.  Drilling
continues to determine the size potential of this exciting new
discovery.”

Results from the main massive sulphide intercepts include:

        --  Hole GRB5D028 intersected 3.71 metres of MS grading 2.2% Cu,
            0.83 g/t Au, 7.13% Zn and 49.73 g/t Ag from 45.96 metres.

        --  HoleGRB5D030 intersected 30.95 metres of MS + SMS + QVS grading
            3.16% Cu, 0.28 g/t Au, 1.29% Zn and 17.40 g/t Ag from 32.05
            metres.  This includes 5 metres grading 7.18% Cu, 0.48 g/t Au,
            2.52% Zn and 37.20 g/t Ag from 48 metres.

        --  HoleGRB5D032 intersected 20.30 metres of MS grading 5.79% Cu,
            0.37 g/t Au, 2.42% Zn and 22.04 g/t Ag from 67.15 metres.  This
            includes 13.19 metres grading 6.48% Cu, 0.43 g/t Au, 3.46% Zn
            and 27.14 g/t Ag from 72.81 metres.

Table 1.  Assay summary for GRB5D028, GRB5D030 and GRB5D032 at Mahab 4. 

     _____________________________________________________________________
    |               MAHAB 4 PROSPECT - SUMMARY of SIGNIFICANT RESULTS     |
    |_____________________________________________________________________|
    |Hole #  |From |  To |Intercept|Mineralisation|Copper|Gold|Zinc|Silver|
    |________|_____|_____|_________|______________|______|____|____|______|
    |        |   m |   m |      m  |              |   %  |g\t |  % |  g/t |
    |________|_____|_____|_________|______________|______|____|____|______|
    |                                                                     |
    |_____________________________________________________________________|
    |GRB5D028|45.96|49.67|   3.71  |Umber + MS    | 2.20 |0.83|7.13|49.73 |
    |________|_____|_____|_________|______________|______|____|____|______|
    |                                                                     |
    |_____________________________________________________________________|
    |GRB5D030|32.05|63.00|   30.95 |MS + SMS + QVS| 3.16 |0.28|1.29|17.40 |
    |________|_____|_____|_________|______________|______|____|____|______|
    |   incl:|48.00|53.00|   5.00  |MS            | 7.18 |0.48|2.52|37.20 |
    |________|_____|_____|_________|______________|______|____|____|______|
    |                                                                     |
    |_____________________________________________________________________|
    |GRB5D032|67.15|87.45|   20.30 |Jasper + MS   | 5.79 |0.37|2.42|22.04 |
    |________|_____|_____|_________|______________|______|____|____|______|
    |   incl:|72.81|86.00|   13.19 |MS            | 6.48 |0.43|3.46|27.14 |
    |________|_____|_____|_________|______________|______|____|____|______|

CODES (Umber-Fe sediment, Jasper, MS = Massive Sulphide, SMS =
Semi-massive Sulphide, QVS = Quartz Vein Stringer
)

Table 2 – Core holes completed at Mahab 4 between January and April,
2011

     _____________________________________________
    |Mahab 4 Drill Summary (January - April, 2011)|
    |_____________________________________________|
    |Hole    |Project|Dip|Azi|Length (m)          |
    |________|_______|___|___|____________________|
    |GRB5D025|Mahab 4|50 |255|74.85               |
    |________|_______|___|___|____________________|
    |GRB5D026|Mahab 4|60 |255|165                 |
    |________|_______|___|___|____________________|
    |GRB5D028|Mahab 4|70 |255|113.15              |
    |________|_______|___|___|____________________|
    |GRB5D030|Mahab 4|60 |255|145.05              |
    |________|_______|___|___|____________________|
    |GRB5D032|Mahab 4|60 |75 |101.25              |
    |________|_______|___|___|____________________|
    |GRB5D035|Mahab 4|60 |255|130.4               |
    |________|_______|___|___|____________________|
    |GRB5D039|Mahab 4|70 |255|122.25              |
    |________|_______|___|___|____________________|
    |GRB5D041|Mahab 4|60 |255|108.25              |
    |________|_______|___|___|____________________|

RESULTS

GRB5D028 (255/70° – Section 3)

This hole was sited to test the northern strike continuation of the
massive sulphides reported previously in drillholes GRB5D011 and
GRB5D020 on Section 2 located 50 metres to the south, refer to Figures
1 and 2 attached to press release on the Company’s website.  GRB5D028 intersected 3.71 metres of umber and MS grading 2.2% Cu, 0.83 g/t Au, 7.13% Zn and
49.73 g/t Ag from 45.96 metres
.  This zone is interpreted to be distal and down dip from the main MS
mound to the west that was tested by subsequent hole GRB5D030 on this
section.  Cu grades are reasonably homogeneous throughout the GRB5D028
intersection, whereas Au, Ag and Zn grades are highest towards the
bottom part of the MS with 1.19metres of MS grading 1.73% Cu, 1.83 g/t Au, 21.12% Zn and 94.24 g/t
Ag from 48.48 metres.

GRB5D030 (255/60° – Section 3)

This hole was sited 25 metres in front of GRB5D028 and intersected a
strong mineralised zone 30.95 metres thick grading 3.16% Cu, 0.28 g/t Au, 1.29% Zn and 17.4 g/t
Ag from 32.05 metres
consisting of two lenses of MS separated by 4.08metres of Jasper, QVS and a dyke.  Jasper and Breccia occurs at the top of the zone and the MS grade decreases downward through SMS into stringer zone QVS.  Grades vary throughout this intersection but there is Au, Ag and Zn
enrichment in MS at the top of the zone, and this whole sequence is considered proximal
to the original MS feeder zone at the seafloor.

The upper MS consists of 22.51 metres of MS and jasper/breccia grading 4.11% Cu, 0.33 g/t Au, 1.68% Zn and 22.15 g/t Ag from 32.05
metres.  This mound zone includes a top and bottom zone richer in Au
and Zn as well as three generally unmineralised dykes with a cumulative
thickness of 4.81 metres.  This main MS intersection contains two Cu/Zn
rich intervals:

        --  3.62 metres of MS grading 3.85% Cu, 0.44 g/t Au, 2.4% Zn and
            24.25 g/t Ag from 33.8 metres.
        --  5 metres of MS grading 7.18% Cu, 0.48 g/t Au, 2.52% Zn and
            37.20 g/t Ag from 48 metres.

The lower MS is less strongly mineralised and consists of 4.36 metres of MS and QVS grading 1.04% Cu, 0.08 g/t Au, 0.14% Zn and 1.23 g/t Ag from 58.64
metres.

GRB5D032 (75/60° – Section 3)

This drillhole was sited within of the footwall basalt ridge and drilled
east to define the western extent and controls on the MS mineralisation
found in the previous two holes on this section.  It intersected 20.30 metres of MS grading 5.79% Cu, 0.37 g/t Au, 2.42% Zn and 22.04 g/t
Ag from 67.15 metres
.  This high-grade MS intersection starts across a steep westerly
dipping main fault zone marking the unmineralised but altered footwall
basalt boundary and includes one 91cm thick dyke.  The basal MS contact
is conformable against weakly altered footwall basalt with no stringer
zone, suggesting it is relative distal compared to the GRB5D030
footwall intersection directly to the west.

Cu grades are reasonably homogeneous throughout the intersection, but
Au, Ag and Zn grades are highest in the central to basal portions of
the MS with 13.19 metres grading 6.48% Cu, 0.43 g/t Au, 3.46% Zn and 27.14 g/t Ag
from 72.81 metres. 
This MS intersection in GRB5D032 is consistent with the similar MS
intersection in GRB5D030 and serves to define a proximal MS wedge
approximately 15 metres true thickness adjacent to the steep westerly
dipping main fault zone at Mahab 4.

GRB5D035 (255/60° – Section 4)

This  hole was designed to further test the strike extensions of the
strong MS intersections achieved in section 3 50 metres to the south
and was sited close to the main fault zone in order to maximise the
chance of hitting proximal copper-rich MS mound mineralisation as in
GBR5D032.

GRB5D035 produced a major seafloor mound MS to SMS intersection
approximately 50 metres thick above a pyritic weakly mineralized
footwall stringer zone down to 111 metres.  The massive sulphide zone
contains a number of barren basalt dykes and sills and also some
significant faults but is generally coherent comprising early pyritic
breccia clasts with subsequent infill by chalcopyrite and sphalerite.

Currently, this major intersection is not fully understood in terms of
its structural setting because subsequent drilling of a step back hole
GRB5D039 on this section failed to intersect the deposit, probably due
to several cross faults observed in the core. However, given the
strength of visible chalcopyrite in the GRB5D035 MS zone, it is
expected to match or exceed the grades in section 3 reported herein.
This impressive zone thus appears to be the central focus of the
deposit tested to date, but it’s down dip and strike extensions are
obscured by several faults whose displacements and orientations are
unknown.

GRB5D041 (255/60° – Section 5)

This hole was sited 50 metres north of GRB5D035 in an equivalent
structural position and tested the possible strike extend beyond the
TEM conductor interpreted to the south. The hole intersected the
seafloor volcanic target position at 40 metres depth as predicted but
there was no mineralisation developed, therefore it appears the deposit
has been wedged or faulted out near the surface between sections 4 and
5 and further drilling is required.

ASSESSMENT

Gentor’s second drilling campaign to test the resource potential of this
exciting VMS discovery at Mahab has produced consistently outstanding
copper grades with zones averaging 3-7% Cu over 20 metre intervals
considered close to true thickness in shallow dipping proximal MS mound
type breccias and with significant Au, Ag and zinc zones mainly in
upper MS and distal positions with metalliferous sediments.

Drilling has confirmed the MS mineralisation formed as a north trending
seafloor mound that dips shallowly east and lenses out into
metalliferous sediments at the favourable Geotimes (V1-1) and Lasail
unit (V1-2) contact.

Holes with an azimuth of 255° and dip of 70°west (see figures attached
to press release on the Company’s website) therefore provide a
reasonable estimate of true thickness of MS intervals. Whereas holes
with an azimuth of 75° and dip of 55-60° east (see sections below)
provide a reasonable estimate of true thickness of Footwall SMS- QVS
stringer zone intervals.

The deposit is cut off to the west by a late reverse thrust that may
have been a reactivated syn-volcanic structure shown in Figure 1
(attached to press release on the Company’s website) that controlled
localization of the deposit, and other faults may wedge the deposit to
the north.

Gentor has yet to test the southern limits of the VTEM conductor being
targeted at this deposit and the current results suggest further
shallow high-grade extensions will be found by ongoing drilling.
Therefore Gentor is confident that a near surface high-grade copper
resource can be defined at this leading prospect.

Qualified Person

The exploration results disclosed in this press release have been
reviewed, verified (including sampling, analytical and test data) and
compiled by Dr. Peter Ruxton who is a Member of the Institute of
Materials, Minerals and Mining (I.M.M.M.), the Company’s President and
Chief Executive Officer and a “qualified person” (as such term is
defined in Canadian National Instrument 43-101 as promulgated by the
Canadian Securities Administrators).

Drill cores for assaying were taken from varying intervals based on
geological interpretation and cut with a diamond saw, with one-half of
the core placed in sealed bags and sent for sample preparation in
Muscat, Oman. The core samples were then crushed to -2mm, split and
pulverized down to 90% passing 75 microns. Approximately 150 grams of
pulverized sample were then shipped to the ALS Laboratory (which is
independent of the Company) in Romania where samples were analyzed for
base metals via XRF techniques and gold via fire assay using a 50g
charge. As part of the Company’s QA/QC procedures, which adhere to
international recognized standards, duplicates, blanks and standards
were inserted into sample batches.

About Gentor

Gentor is a mineral exploration company whose projects include copper
and gold properties in the Sultanate of Oman and a
molybdenum-tungsten-silver property in East Central Idaho, U.S.  The
Company’s strategy is to create shareholder value by developing highly
prospective mineral properties around the globe, with current focus in
the Sultanate of Oman.  In Oman, Gentor is partnered with Al Fairuz
Mining Company LLC on its Block 5 exploration tenement and Al Zuhra
Mining Company LLC on Block 6.

Cautionary Notes

This press release contains certain statements that may be deemed
“forward-looking statements” within the meaning of the Private
Securities Litigation Reform Act of 1995. All statements in this press
release, other than statements of historical fact, that address
potential future production, resource and reserve potential,
exploration drilling activities and events or developments that the
Company expects to occur, are forward-looking statements.
Forward-looking statements are statements that are not historical facts
and are generally, but not always, identified by the words “expects”,
“plans” “anticipates”, “believes”, “understands”, “intends”,
“estimates”, “projects”, “potential” and similar expressions, or that
events or conditions “will”, “would”, “may”, “could” or “should” occur.
Information inferred from the interpretation of drilling results and
any information concerning potential mineral resources may also be
deemed to be forward-looking statements, as it constitutes a prediction
of what might be found to be present when and if a project is actually
developed. Such statements are not guarantees of future performance and
actual results may differ materially from those in the forward-looking
statements. Factors that could cause the actual results to differ
materially from those in forward-looking statements include market
prices, exploitation and exploration successes, continued availability
of capital and financing, and general economic, market or business
conditions.

The United States Securities and Exchange Commission (the “SEC”) permits
mining companies, in their filings with the SEC, to disclose only those
mineral deposits that a company can economically and legally extract or
produce. U.S. investors are cautioned not to assume that any disclosure
of mineralization contained in this press release is economically or
legally mineable. U.S. investors are urged to closely consider all of
the disclosures in the Company’s reports filed pursuant to the
Securities Exchange Act of 1934 which may be secured from the Company,
or from the SEC’s website at http://www.sec.gov/edgar.html.

 

SOURCE Gentor Resources Inc.


Source: newswire



comments powered by Disqus